NSEE HXQ908 Automatic Gate Lock Remote Control Latch In-Outward Antenna Receiver

Description

Product features:
Dual-core and dual-system, 4 different ways to open and lock , (2 ways with remote controller, 1 with passwords , 1 with GSM mobile phone ), increase the function of the spare circuit to ensure the normal use;
The unique design of external mounting plate, easier installation , firmer;
The remote control with digital conversion system in sound option, which can not be decoded and duplicated, preventing technical unlocking;
Super power-saving control mode, low power consumption, 4 No. 5 batteries can support normal standby for more than 16 months;
The lock body without electricity, the lock can be used with spare battery as usual. You need to worry that the lock can not be unlocked when the battery is dead ;
Long service life, there is no wear with the operation of 300,000 times;
Anti rust battery box, the battery box spring is made of stainless steel , permanent use;
The bolt and main parts of the panel are made of stainless steel, never fade;
Can be added with a password keyboard controller and use the password to unlock. Only knowing the password can the remote controller be used as a safer alternate ;
Low voltage alarm prompting function and lock protection function under voltage: when running out of the battery power , the remote controller can't lock the door (remote control lock can not be locked and it gives out alarm sound). The remote controller can be used normally, and you should replace the battery;
Can be widely used in
Office, home furnishing, hotel, any security door, household door, corridor door, wooden door, garage door
Technical parameters:
Remote-controlled distance: 0-10 m
Number of operations: 300,000 times
Power supply mode: 4 NO5 dry batteries and 23A12V battery , either of the ways can be used normally.
Battery life: 4 batteries can support normal standby for more than 16 months
The unlocking current: 100 mA
Service environment: temperature of -20 ℃ ~70 ℃, humidity of 20%~80%
The shift motion of bolt : 23mm
Size: 77mm x 133mm x 37mm
Product picture and introduction of part name
1. Manual knob
2. Battery box cover plate
3. Battery box cover plate screw
4. Ear of the bolt
5. Receiving antenna
6. Lock body fixed plate
7 Common unlocking button
8 Spare unlocking button
Instructions
1 Scope of application:
Office, home furnishing, hotel, any security door, household door, corridor door, wooden door, garage door etc.
2 The installation steps:
1 ） Close the door, place the mounting plate and the bolt between the doorframe and the door tightly, paint several locating holes, then directly use electric drill to fight screws to fix it (refer to
the Figure )
2) Fix the lock body bottom plate, tighten 4 screws to fix the lock body. The corresponding bolt base should not be tight, with 2 mm to ensure opening or locking without interference ;
3) After installation, people should use the remote controller inside the door to see whether the lock is flexible , and the bolt should not be stuck .
3. Method of replacing battery:
Unscrew the battery cover screw, open the cover plate, remove the batteries and place 4 new No 5 battery. ( Nanfu, Duracell batteries are recommended)
4 Application method:
Commonly used circuit switch lock :
Lock the door: press (0.5 seconds) on the remote controller, the lock is locked when you hear the sound of the bolt, and the horn of lock body makes one sound ;
Open the door: press (0.5 seconds), the lock is unlocked when you hear the sound of the bolt, and the horn of lock body makes three sounds;
Standby circuit switch lock: standby circuit is usually in off position. When using it, you should
beat the door connecting with the lock body (slightly larger strength ), with a frequency of about
once every 0.5 seconds, do 3--5 times (if the door is very thick, more beats are appropriate ), do
not beat the door until the horn of the lock body make one sound, while a standby circuit is
switched on, immediately press a set of buttons on the bottom of the remote controller, then you
can control the switch lock. If you do not press the set of buttons timely when hearing the sound of
the horn, the standby lock body system automatically shuts down. You can repeat the above steps
if you want to use standby switch lock.
In the process of using, if you hear the alarm sound which shows low voltage for
many times, you should replace the battery. Please replace a group of spare 12V
batteries together.
5．Match code for remote controller of the remote control lock ( It has been matched when
delivery)
1） This lock use SCM to match the code intelligently, after the installation for the battery in host, press the matching code key st2 in the host lock body and release it when hearing one sound let out by the horn, and then press matching code key st2 immediately and the horn let out another sound (press and hold), now press a group of keys in the remote controller (for about one second), hearing the horn let out two sounds on end, set up other remote controller. You can press the key in the remote controller and will hear three sounds let out by the horn, then release matching code key st2 and the remote controller has been set up by then.
2） Repeat steps above in case of requiring setting up other remote controllers.
3） Methods for setting up standby system: Press standby setting up key (ST1) when setting up standby system and the method is the same as above mentioned, except that the standby keys in the remote controller are as keys below.
4） This lock can be matched with password remote controller also（. Refer to the picture, and purchase otherwise in case of need).
Concrete operations:Before operating on password remote controller, long press common circuit matching code key for 8 to 10 seconds first to delete all codes of the remote controller, then press matching code key ST2 in lock body(release after one press), and then press it again (press and hold), then press key C, hearing the lock body let out three sounds (HXQ901 model let out one sound and flash five times) indicates code has been matched. Then set password by pressing key C, entering password you want (1-6 random numbers) , pressing key C to confirm. Hearing three sounds of “ tck tck tck” indicates that you have set the password correctly.( Do not release each press until hearing the sound)
Application method of password remote controller
. Press key C in password remote controller, then keys 123456, then key C (do not press too fast),
and then carry out switch operations.
. Operations of switch lock of password remote controller
. Press key C (one sound), then press keys 1-2-3-4-5-6- to unlock.
. Press key C (one sound), then press keys 1-2-3-4-5-6- to lock.
5）．Delete remote controller
In case that the controller is lost carelessly, please long press the matching code key(st2) in the lock body to make the buzzer let out a sound, about 8 seconds later the horn gives another sound and then release the key. Total two sounds indicate that all switch lock keys(including password remote controller, telephone lock remover, mobile phone lock remover) in common use of the remote controller have been deleted, and then match the code again for the remote controller in
hand. Press the standby matching code key (st2) for about 8 seconds to delete the standby circuit, with the same methods as above.
6). Application method for telephone unlocking controller
. Application method for operating GSM voice phone lock remover
（1） Installation for SIM card
. Insert GSM mobile phone card.
（2） Receive the GSM mobile phone number in the host according to dialing GSM voice phone lock remover with mobile phone (telephone),enter the password when achieving ringing times that have set (In default, ringing once, the host answers automatically; enter password by pressing keys of mobile phone or telephone; the factory setting password is:1234 )and operate immediately if prompted the password is valid.
Concrete operations are as follows: Insert GSM mobile phone card
Press key 6: unlock, one second later press key 7: shut up unlocking
Common problems handling
“Three guarantees ” ( for repair replacement or compensation of faulty products ) service card after sales
Notes:
1. To enjoy “three guarantees ” ( for repair replacement or compensation of faulty products ) using this card is only in accordance with the lock within models above.
2. Offer this card when enjoying “three guarantees ” ( for repair replacement or compensation of faulty products )
3. This card takes effect after the lock sales unit has sealed and the operator has signatured.
4. One-year free warranty, and the remote controller has three-month free warranty;
5. Start date of warranty period shall subject to invoicing date;
6. In case of one of the conditions below, are out of the scope of warranty.
. Improper use, safe keep and maintenance by consumer result in damage;
. Man made damages or unauthorized dismounting are out of the scope of warranty.